
Clay heat-insulating refractory bricks refer to lightweight refractory products containing 30% to 46% Al2O3. Clay heat-insulating refractory bricks use clay clinker or lightweight clinker and plastic clay as the main raw materials. They use refractory clay, floating beads, refractory clay clinker, and add binders and sawdust. After batching, mixing, molding, drying and firing, they can produce products with a volume density of 0.3 to 1.5 g/cm'. Usually, the combustible method is used for production, and the chemical method or foam method can also be used to form a porous structure. The ingredients are mixed with water to form a plastic mud or mud, which is extruded or cast into a mold. After drying, it is fired in an oxidizing atmosphere at 1250 to 1350C. The volume density of commonly used lightweight clay bricks is 0.75 to 1.50 g/cm3, and the compressive strength is 2.0-5.9 MPa. Clay heat-insulating refractory bricks are widely used, mainly used as heat-insulating materials in various industrial furnaces that do not contact molten materials and have no corrosive gas effects, and the use temperature is 1200~1400C. According to the Chinese standard (GB3994--1983), clay heat-insulating refractory bricks are divided into NG-1.5, NG-1.3a, NG-1.3b, NG-1.0, NG-0.9, NG-0.8NG-0.7, NG-0.6 and ten other grades according to volume density.
yleisesti käytetty tuotanto prosessi savelle eristävälle tulenkestävälle tiilelle on palaminen lisäys menetelmä kelluvilla helmillä, ja vaahto menetelmä voi myös olla käytettävä.

Tuotteet Kuvaus
Raw materials, binders and sawdust for clay-based heat-insulating refractory bricks (1) The raw materials are refractory clay, clay clinker and floating beads. The chemical composition of floating beads fluctuates greatly. In order to obtain products that meet the quality standards, it is necessary to select raw materials for clay-based heat-insulating refractory bricks with an AlO: content greater than 30%, a Fez0: content less than 3%, and a refractoriness greater than 1610 degree . Most of the floating beads are closed hollow spheres with thin walls and high strength. Their volume density is 0.38~0.44gcm', their color is grayish white, and their particle size is 20~250pm, of which 50~150μm is more common. The whole bead rate is greater than 95%. Inclusions can be removed by screening or rinsing. If rinsed, they should be dried or spun. (2) Clinker fines and floating beads are both lean aggregates. The floating beads are round or nearly round, with a smooth surface, fine particles, and a large specific surface area, which requires the binder to have a strong binding property. The main binders are: refractory clay, sulfite pulp waste liquid, aluminum sulfate, water glass, phosphoric acid and phosphate, dextrin resin, etc. Refractory clay has high binding, dispersibility, plastic refractoriness and sintering properties. It is also cheap and has abundant resources. Therefore, most mixtures are based on refractory clay. According to the product type, bulk density and technical requirements, add an appropriate amount of organic or inorganic binder. (3) Sawdust should be screened and the particle size should be less than 1-2 mm.
Ainesosat savelle lämpöä eristävälle tulenkestävälle tiilelle tilavuus tiheys tuotteen on erilainen, ja kelluvien helmien määrä lisätty on myös erilainen. Yleensä, se vaihtelee 10% ja 70%. Pienempi tilavuus tiheys tuote, the lisää se lisätty lisää savi klinkkeri jauhe to ainekset vähentää tilavuus kutistuminen aiheutettu muodonmuutos kelluvat helmet. Sisään järjestyksessä vähennä määrä kelluvia helmiä, paranna vahvuus puolivalmiista tuotteista ja vähennä kutistuminen polttamisen jälkeen, lisää sopiva määrä sahanpurua.
Sekoittaminen savipohjainen lämpöä eristävä tulenkestävä tiili muodostaa materiaali kosteus sekoittuu tasaisesti ja parantaa muovaus suorituskyky savesta. Yleisesti käytetty sekoitus laitteet sisältää hiekka sekoittimet ja pakotettu vastavirta sekoittimet. Olemassa kaksi toimintamenetelmät: yksi on lisättävä kelluvat helmet, sahanpuru, sideaine, vesi, savi ja klinkkeri jauhe järjestyksessä. Sekoita 5 to 6 minuuttia saada a savi materiaali kelluvilla helmillä tai sahanpuru as the ydin, sideaine ja savi as ulko kerros, ja kuiva jauhe as uloin kerros. The muu on lisää kelluvat helmet, klinkkeri jauhe, sidonta savi ja sahanpuru sisään koneeseen, sekoitus 2 3 minuuttiin, lisää vettä ja sideaine, ja märkä sekoita 3 4 minuuttia. The sekoitettu savi voidaan muovata 12 24 tunnin jälkeen. Kosteus pitoisuus savi riippuu tekijöistä kuten tuote tilavuus tiheys, ainesosa suhde, ja muovausmenetelmä. Yleensä, kosteus pitoisuus savi on 20% to 30%.
Savi savi lämpöä eristävän tulenkestävän tiilen on enimmäkseen tehty käsin ja koneella puristamalla. Kone puristus pitäisi käyttää a 150~300kN tiili puristin. Lujuus tiilien jälkeen muovaaminen on erittäin matala, niin ne pitäisi käsitellä varoen; puolivalmisteet tuotteet kanssa monimutkaiset muodot, suuri yksittäinen paino tai pieni tilavuus tiheys voidaan pitää kuormalavoilla tai vaneri estää tiilet alkaen muodonmuutoksesta ja vaurioista.
The packing and firing of clay heat-insulating refractory bricks are side-loaded, requiring flatness, stability and straightness, and rice husks are sprinkled layer by layer. Hand gaps should be left between bricks. The kiln loading height is generally 1.5~1.8m, and products with a volume density of less than 0.6g/cm* should not exceed 1.2m: and should be loaded in the low-temperature part of the kiln. When the products are fired in a downdraft kiln or tunnel kiln, the kiln temperature should be uniform. The maximum firing temperature varies depending on the quality of the floating beads, clay and the volume density of the products. Usually, the products with bulk density of 0.4~0.6g/cm degree have a fire-stop temperature of 1220~1250 degree ; the products with bulk density of 0.8~1.0g/cm degree have a fire-stop temperature of 1250~1280 degree , and the heat preservation time is 6~8h. The cooling kiln speed is similar to that of clay bricks. In actual production, products with different bulk densities are often fired in the same kiln. Therefore, according to the temperature distribution in the kiln, products of different brands are installed in different parts to improve the firing quality.
Käyttö savesta eristävä tulenkestävä tiilet:
Clay heat-insulating refractory bricks are widely used, mostly in the heat insulation layer of thermal equipment and industrial furnaces. They can be used in areas without strong erosion and scouring of high-temperature molten materials. Some surfaces in direct contact with flames are coated with a refractory coating to reduce erosion by slag and scouring by furnace gas and dust, and reduce damage. The working temperature of the product does not exceed the test temperature of the reburning line change.
|
Brändi |
HXP-1.3 |
HXP{{0}}}.0 |
HXP-0.9 |
HXP-0.8 |
HXP-0.7 |
HXP-0.6 |
HXP-0.5 |
|
Bulkki tiheys g/cm3 Pienempi kuin tai yhtä suuri |
1.3 |
1.0 |
0.9 |
0.8 |
0.7 |
0.6 |
0.5 |
|
Normaali lämpötila puristava lujuus MPa Suurempi kuin tai yhtä suuri |
9.0 |
7.0 |
6.0 |
5.0 |
4.0 |
3.0 |
2.5 |
|
Uudelleenlaukaisu linja muutokset Vähemmän tai yhtä suuri 2%( aste ×h) |
1400×12 |
1300×12 |
1250×12 |
1250×12 |
1250×12 |
1200×12 |
1150×12 |
|
(350 % c2 % b125 astetta ) vähemmän kuin tai yhtä suuri kuin |
0.47 |
0.35 |
0.32 |
0.27 |
0.25 |
0.22 |
0.19 |
Suositut Tagit: kevyt savi eristys tiili, Kiina kevyt savi eristys tiili valmistajat, toimittajat, tehdas



